Mô tả
PTO Shaft Replacement of Weasler 55 Series
Replacement Weasler Series 55 PTO Shaft
- 1-3/8″- 6 Spline Slide-Lock Tractor Yoke
- Cần có bộ dụng cụ Cross Kit.
- Yêu cầu triển khai Yoke.
- 106 HP @ 540 RPM
- Chiều dài khi nén: 48 inch (Kích thước A)
Specifications Of 55 Series PTO shaft
| Spec. | Imperial | Metric |
|---|---|---|
| Lỗ khoan 1 | Giá đỡ đầu âm | |
| Lỗ khoan 2 | Giá đỡ đầu âm | |
| Chiều dài nén (đóng) | 37.38 inches | 949 mm |
| Chiều dài tổng thể khi nén | 48.00 inches | 1219 mm |
| Kết nối 1 | CÁNH TAY ÉP | |
| Kết nối 2 | CÁNH TAY ÉP | |
| Chiều dài mở rộng | 61.13 inches | 1553 mm |
| Chiều dài tổng thể kéo dài | 72.00 inches | 1829 mm |
| HP@1000RPM | 164 HP | 122 kilowatts |
| HP@540RPM | 106 HP | 79 kilowatts |
| Chiều dài | 48.00 inches | 1219 mm |
| Đường kính ngoài | 7.28 inches | 185 mm |
| Kích thước đóng gói | 37.38″ L × 7.28″ H × 7.28″ W | 95cm L × 18cm H × 18cm W |
| Khối lượng vận chuyển | 1981.08 in3 | 32464 cm3 |
| Trọng lượng vận chuyển | 41.90 pounds | 19 kilograms |
| Cân nặng | 41.90 pounds | 19 kilograms |
Weasler 55 Series PTO Shaft Parts
 |
 |
 |
 |
| Tractor Yoke | Cross & Bearing Kit | Shaft | Shaft Weld Yoke |
 |
 |
 |
 |
| Slip Sleeve | Tube | Tube Weld Yoke | Implement Yoke |
 |
 |
 |
 |
| Yoke & Shaft Assembly | Yoke & Tube Assembly | Drivelines | Guard & Guard Bearing |
The PTO shaft plays a vital role in transmitting power from the tractor to the attached implement. Components of a Trục PTO include inner and outer PTO yokes, universal joints, safety chains, and safety guards. There are several different types of PTO shafts to choose from, so it is imperative to choose the right one for your equipment and application.
Ever-power offers three different types of PTO shafts: North American, German, and Italian. Each style includes multiple series options, including a variety of bearing diameters, overall cover-to-cover lengths, and snap rings. The most accurate way to determine the correct series is to measure the outside diameter of the bearing cap and the U-joint from one end of the cap to the other. The position of the snap ring is another determining factor.
How to Measure PTO Shaft Parts?
Correctly measuring shaft parts is critical to selecting the correct PTO series size. Each piece needs to be measured in a specific way to fit the standard size. Follow the steps below to ensure you get the correct measurements and order parts for your tractor.
1. Measuring the shaft
To measure your shaft, you should first make sure it is in the closed position when the shaft is smallest. Use a tape measure to record the length from the outside of each yoke. This measurement is the closed length. Use this measurement to find the correct series size for your tractor horsepower.
Make sure you also know if you have shear pins, clutches or splined implement ends.
2. Measure the universal joint
When measuring a universal joint, measure the length from one outer end to the other. You will also need to record the width of one end of the universal joint. Use these numbers to find the proper gimbal size.
3. Put them all together
You will need both of the measurements listed above to find a PTO shaft part that works well for your tractor. You can use the PTO Yoke Size Chart to get the right size or use our handy PTO Series Discovery Tool.
Trục PTO cho hộp số nông nghiệp
Agricultural equipment includes a variety of PTO shafts. Each one is connected by yokes at each end and rotates between 540 and 1,000 rpm. A safety shield is commonly installed on both ends of a PTO shaft to protect the operator. These protective shields are also found in tractors and agricultural implements, ensuring maximum efficiency. The use of internal yokes also provides added safety.
Cái hộp số nông nghiệp is designed to change the output speed of a PTO shaft. It can be used as a decreasing or increasing ratio gearbox. With the decrease ratio gearbox, it reduces the PTO shaft’s speed from 1000 rpm to 540 rpm, allowing you to use equipment designed for 540 rpm. On the other hand, an increasing ratio gearbox increases the speed of the PTO shaft from 540 rpm to 1000 rpm.
Nếu bạn cũng cần hộp số nông nghiệp, hãy nhấp vào đây:https://hzpt.com/agricultural-pto-gearbox/ and contact us!
Trục PTO Nhà sản xuất
1. Materials
Our company purchases steel from many large steel groups such as Hangzhou Steel Plant, Shanghai Bashan Steel Plant, Beijing Shuge Steel Plant, etc. The steel has good mechanical properties and chemical composition stability. It keeps the shaft high quality.
2. Manufacturing Process
①we have our own high-precision mold manufacturing digital machining center in a specialized mold workshop, the excellent mold makes the product beautiful in appearance and accurate in size.
②Sandblasting is used to remove the oxidized surface and make the surface smooth, uniform, and beautiful.
③in terms of heat treatment: we use a controlled atmosphere automatic heat treatment furnace,
3. Quality Control
Quality control is strictly enforced from the procurement of raw materials from the warehouse to the different processing processes, to the final packaging. 100% inspection during production.
4. Production capacity
Single PTO, 16,000 units per month.
