Opis
PTO Shaft Replacement of Weasler 55 Series
Replacement Weasler Series 55 PTO Shaft
- 1-3/8″- 6 Spline Slide-Lock Tractor Yoke
- Requires Cross Kit.
- Requires Implement Yoke.
- 106 HP @ 540 RPM
- 48″ Compressed Length (Dim. A)
Specifications Of 55 Series PTO shaft
| Spec. | Imperial | Metric |
|---|---|---|
| Otwór 1 | Jarzmo ujemne | |
| Otwór 2 | Jarzmo ujemne | |
| Długość skompresowana (zamknięta) | 37.38 inches | 949 mm |
| Skompresowana długość całkowita | 48.00 inches | 1219 mm |
| Połączenie 1 | Ramiona jarzma | |
| Połączenie 2 | Ramiona jarzma | |
| Wydłużona długość | 61.13 inches | 1553 mm |
| Wydłużona całkowita długość | 72.00 inches | 1829 mm |
| KM przy 1000 obr./min | 164 HP | 122 kilowatts |
| KM przy 540 obr./min | 106 HP | 79 kilowatts |
| Długość | 48.00 inches | 1219 mm |
| Średnica zewnętrzna | 7.28 inches | 185 mm |
| Wymiary wysyłki | 37.38″ L × 7.28″ H × 7.28″ W | 95cm L × 18cm H × 18cm W |
| Objętość wysyłki | 1981.08 in3 | 32464 cm3 |
| Waga wysyłkowa | 41.90 pounds | 19 kilograms |
| Waga | 41.90 pounds | 19 kilograms |
Weasler 55 Series PTO Shaft Parts
 |
 |
 |
 |
| Jarzmo ciągnika | Zestaw krzyża i łożyska | Wał | Jarzmo spawane wału |
 |
 |
 |
 |
| Rękaw ślizgowy | Rura | Jarzmo spawane rurą | Jarzmo narzędziowe |
 |
 |
 |
 |
| Zespół jarzma i wału | Zespół jarzma i rury | Układy napędowe | Osłona i łożysko osłony |
The PTO shaft plays a vital role in transmitting power from the tractor to the attached implement. Components of a Wał odbioru mocy include inner and outer PTO yokes, universal joints, safety chains, and safety guards. There are several different types of PTO shafts to choose from, so it is imperative to choose the right one for your equipment and application.
Ever-power offers three different types of PTO shafts: North American, German, and Italian. Each style includes multiple series options, including a variety of bearing diameters, overall cover-to-cover lengths, and snap rings. The most accurate way to determine the correct series is to measure the outside diameter of the bearing cap and the U-joint from one end of the cap to the other. The position of the snap ring is another determining factor.
How to Measure PTO Shaft Parts?
Correctly measuring shaft parts is critical to selecting the correct PTO series size. Each piece needs to be measured in a specific way to fit the standard size. Follow the steps below to ensure you get the correct measurements and order parts for your tractor.
1. Measuring the shaft
To measure your shaft, you should first make sure it is in the closed position when the shaft is smallest. Use a tape measure to record the length from the outside of each yoke. This measurement is the closed length. Use this measurement to find the correct series size for your tractor horsepower.
Make sure you also know if you have shear pins, clutches or splined implement ends.
2. Zmierz przegub uniwersalny
When measuring a universal joint, measure the length from one outer end to the other. You will also need to record the width of one end of the universal joint. Use these numbers to find the proper gimbal size.
3. Put them all together
You will need both of the measurements listed above to find a PTO shaft part that works well for your tractor. You can use the PTO Yoke Size Chart to get the right size or use our handy PTO Series Discovery Tool.
Wał odbioru mocy do przekładni rolniczych
Agricultural equipment includes a variety of PTO shafts. Each one is connected by yokes at each end and rotates between 540 and 1,000 rpm. A safety shield is commonly installed on both ends of a PTO shaft to protect the operator. These protective shields are also found in tractors and agricultural implements, ensuring maximum efficiency. The use of internal yokes also provides added safety.
Ten skrzynia biegów rolnicza is designed to change the output speed of a PTO shaft. It can be used as a decreasing or increasing ratio gearbox. With the decrease ratio gearbox, it reduces the PTO shaft’s speed from 1000 rpm to 540 rpm, allowing you to use equipment designed for 540 rpm. On the other hand, an increasing ratio gearbox increases the speed of the PTO shaft from 540 rpm to 1000 rpm.
Jeśli potrzebujesz również przekładni rolniczych, kliknij tutaj:https://hzpt.com/agricultural-pto-gearbox/ and contact us!
Wał odbioru mocy Producent
1. Materials
Our company purchases steel from many large steel groups such as Hangzhou Steel Plant, Shanghai Bashan Steel Plant, Beijing Shuge Steel Plant, etc. The steel has good mechanical properties and chemical composition stability. It keeps the shaft high quality.
2. Manufacturing Process
①we have our own high-precision mold manufacturing digital machining center in a specialized mold workshop, the excellent mold makes the product beautiful in appearance and accurate in size.
②Sandblasting is used to remove the oxidized surface and make the surface smooth, uniform, and beautiful.
③in terms of heat treatment: we use a controlled atmosphere automatic heat treatment furnace,
3. Quality Control
Quality control is strictly enforced from the procurement of raw materials from the warehouse to the different processing processes, to the final packaging. 100% inspection during production.
4. Production capacity
Single PTO, 16,000 units per month.
